DLP – LOCTITE IND147
LOCTITE 3D IND147 is a black, high-temperature resin for DLP 3D printing from Henkel. After a full thermal post-cure, it has a heat deflection temperature above 230°C and very high hardness, with good dimensional stability and enough toughness to stand up to repeated molding cycles. Henkel designed it for high-temperature, low-pressure tooling, such as molds for polyurethane and silicone casting.
What LOCTITE IND147 Is Best For
- Molds for polyurethane (urethane) and silicone casting
- High-temperature, low-pressure tooling
- Prototypes of parts that see high temperatures
- Custom molds and mold inserts for low-pressure processes
When another material is a better fit
- Need injection mold inserts: Rigid 10K
- Need a heat-resistant resin for detailed parts: SLA High Temp Resin
- Need a tough part that sees moderate heat: MJF Nylon 12
Key Material Facts
- Heat deflection temperature of 235–291°C at 0.455 MPa and 136–163°C at 1.82 MPa, after thermal post-cure
- Glass transition temperature of 205–212°C
- Very hard: 94 Shore D
- High stiffness: 3,190 MPa tensile modulus
- Low water absorption: 0.24% after 24 hours
- Good surface finish for mold cavities
LOCTITE IND147 Material Properties
Version note: we print LOCTITE 3D IND147 from Henkel. Values below come from Henkel’s technical data sheet (version 2025/07/02), for fully post-processed parts.
Mechanical and thermal properties (from Henkel’s published data sheet; fully post-processed, including a 3-hour thermal cure at 170°C)
| Property | Metric | English | Method |
|---|---|---|---|
| Tensile strength at break | 67 MPa | 9,700 psi | ASTM D638 |
| Tensile modulus | 3,190 MPa | 463 ksi | ASTM D638 |
| Elongation at break | 2.4% | 2.4% | ASTM D638 |
| Flexural strength at break | 120 MPa | 17,400 psi | ASTM D790 |
| Flexural modulus | 3,690 MPa | 535 ksi | ASTM D790 |
| Notched Izod impact | 14.6 J/m | 0.27 ft-lbf/in | ASTM D256 |
| Hardness | 94 Shore D | 94 Shore D | ASTM D2240 |
| Heat deflection temperature @ 0.455 MPa | 235–291°C | 455–556°F | ASTM D648 |
| Heat deflection temperature @ 1.82 MPa | 136–163°C | 277–325°F | ASTM D648 |
| Glass transition temperature | 205–212°C | 401–414°F | ASTM E1640 |
| Water absorption (24 hr) | 0.24% | 0.24% | ASTM D570 |
| Density | 1.26 g/cm³ | 0.046 lb/in³ | ASTM D792 |
Thermal and electrical properties
| Property | Value | Method |
|---|---|---|
| Coefficient of thermal expansion (25–200°C) | 114 µm/m·K | ASTM E831 |
| Thermal conductivity | 0.20 W/m·K | ASTM D5930 |
| Volume resistivity | 3.6 × 10¹⁶ ohm-cm | ASTM D257 |
| Dielectric strength | 29 kV/mm | ASTM D149 |
| Dielectric constant, 1 kHz | 3.0 | ASTM D150 |
More information on LOCTITE IND147 is available from Henkel (LOCTITE 3D), the material manufacturer.
IND147 reaches its full heat resistance only after a thermal post-cure at 170°C for 3 hours, on top of the standard UV cure. We do this full thermal post-cure as standard, so your parts get the properties listed above. Very stiff, hard resins like this one are brittle, with about 2.4% elongation at break, so it suits low-pressure molds better than parts that flex or take impacts. For injection mold inserts, we usually recommend Rigid 10K, which we print at fine layers specifically for molding.
DLP builds parts in small to medium sizes, up to 13.9″ × 7.7″ × 13.8″ in one piece, at 0.1 mm (0.004″) layers. SLA and DLP are both resin processes, so our SLA Part Design Guide applies here too. It covers wall thickness, supports, hole and pin sizes, and how to get the most accurate resin parts.
Finish and Color Options
IND147 parts are black. We ship DLP parts with the supports removed. DLP parts come off the printer with a smooth surface, so they often need little more than that. Sanding, painting, Cerakote, and heat-set threaded inserts are available on request and quoted per part. See all of our finishing and post-processing options.
LOCTITE IND147 Part Gallery



Related Resources
- DLP 3D printing overview
- Resin part design guide (SLA and DLP)
- Accuracy of 3D printed parts
- Machine and material comparison
If you like what you see...
You should sign up for our quarterly email newsletter! We send out a summary of all the latest testing videos, design guides, and anything else cool that has been added to the F3DP website 4 times a year.
We hate spam as much as you do so we only send all killer content and no filler BS!