SLA – RP 105W
RP 105W is an opaque white resin for SLA 3D printing, supplied by RP America. It balances strength, stiffness, and toughness with crisp detail and a clean, paint-ready surface. We run RP 105W on our largest SLA printer, so it is our go-to material for large one-piece parts up to 55″ × 27″ × 19″.
What RP 105W Is Best For
- Large one-piece prototypes up to 55″ × 27″ × 19″
- Functional prototypes for fit, form, and light-duty function
- Enclosures, bezels, and consumer product housings
- Automotive interior prototypes and validation fixtures
- Aerospace concept models and wind tunnel shapes
- Architectural massing models and display parts
- Master patterns for silicone molding and paint or texture studies
When another material is a better fit
- Need high impact resistance: Accura Xtreme White 200
- Need a flexible, polypropylene-like part: Accura 25
- Need higher heat resistance: High Temp Resin
Key Material Facts
- Opaque white resin with excellent detail and surface quality
- Balanced strength, stiffness, and toughness (58–70 J/m notched Izod)
- High dimensional accuracy for visual models and test fits
- Easy to sand, prime, and paint
- Typical layer thickness: 0.002–0.006 in (0.05–0.15 mm)
- Builds single parts up to 55″ × 27″ × 19″ with no splits or glue joints
- Works with glue joints and light welding; printed threads are possible, but Helicoil inserts are recommended
RP 105W Material Properties
Version note: RP 105W is supplied by RP America, our partner for large-format SLA materials and service.
Mechanical and thermal properties (UV post-cured, typical values from the supplier data sheet)
| Property | Metric | English |
|---|---|---|
| Tensile strength | 27–31 MPa | 3,900–4,500 psi |
| Tensile modulus | 2180–2395 MPa | 316–347 ksi |
| Elongation at break | 12–20% | 12–20% |
| Flexural strength | 68–75 MPa | 9,860–10,880 psi |
| Flexural modulus | 2690–2755 MPa | 390–400 ksi |
| Notched Izod impact | 58–70 J/m | 1.1–1.3 ft-lbf/in |
| Heat deflection temperature @ 0.45 MPa (66 psi) | 55–65°C | 131–149°F |
| Glass transition temperature | 55–70°C | 131–158°F |
| Hardness | 76–82 Shore D | 76–82 Shore D |
| Density | 1.14–1.16 g/cm³ | 0.041–0.042 lb/in³ |
More information on RP 105W is available from RP America, the material manufacturer.
RP 105W runs on our largest SLA printer, which can build single parts up to 55″ × 27″ × 19″ (1,397 × 686 × 483 mm) with no splits or glue joints. For parts larger than that, we can split the model and bond the sections. See our glue strength guide for joint options.
Like most SLA photopolymers, RP 105W is meant for indoor use. Prolonged UV exposure can cause yellowing and embrittlement, so paint the part or choose another material for outdoor service. Its heat deflection temperature is about 55–65°C (131–149°F), so it is not a good fit for high-heat applications.
Design Tips for RP 105W
SLA parts are printed with supports that leave small marks where they touch the part. We orient each RP 105W part so those marks land on non-critical surfaces, so tell us which faces are cosmetic or need to hold tight dimensions. Keep wall thickness as uniform as you can, and add drain holes to any hollow section so uncured resin can be cleaned out.
Our SLA Part Design Guide covers wall thickness, hole and pin sizes, snap fits, and how to get the most accurate SLA parts.
Finish and Color Options
RP 105W parts are opaque white. The resin sands, primes, and paints well, and we offer all of our standard SLA finish levels. Unless you specify otherwise, we ship parts with Level 1 support sanding.
- Level 0: Strip and ship – excess material and supports removed; support surfaces left rough.
- Level 1: Support sanding – supports removed and support surfaces sanded smooth. This is our standard finish.
- Level 2: Matte finish – support surfaces sanded, rough areas lightly sanded, and the whole part bead blasted for a uniform finish.
- Level 3: Mold master – layer lines sanded off the entire part and bead blasted, ready to serve as a master for silicone molding.
- Level 4: Paint prep – layer lines sanded off the entire part and primed, ready for paint.
- Level 5: Cerakote – layer lines sanded off the entire part and sprayed with Cerakote.
We can also paint parts to a requested color. See all of our finishing and post-processing options.
RP 105W Part Gallery














Related Resources
- SLA 3D printing overview
- SLA part design guide
- Accuracy of 3D printed parts
- Machine and material comparison
RP 105W FAQ
How strong is RP 105W compared to other SLA resins?
RP 105W has a balanced stiffness and toughness profile, with tensile strength around 27–31 MPa and hardness of about 76–82 Shore D. It works well for functional mockups and cosmetic parts, but it is not a high-impact or high-heat material.
What temperature can RP 105W withstand?
Its heat deflection temperature is about 55–65°C (131–149°F) at 66 psi. For hotter applications, consider High Temp Resin or another process.
How accurate are RP 105W parts?
RP 105W produces sharp features and smooth surfaces. With the right design allowances and orientation, it holds detail well enough for snap-fit trials, covers, and enclosures. See our 3D printed part accuracy guide for tolerances.
Can RP 105W be used outdoors?
It is best used indoors. Long-term UV exposure can cause yellowing and embrittlement. Painting the part helps, or we can suggest a better material for outdoor use.
If you like what you see...
You should sign up for our quarterly email newsletter! We send out a summary of all the latest testing videos, design guides, and anything else cool that has been added to the F3DP website 4 times a year.
We hate spam as much as you do so we only send all killer content and no filler BS!
