FDM – OBSIDIAN NYLON 6+CF Printing Material

Last updated: November 13, 2026

Obsidian Nylon 6+CF v2 is a carbon fiber reinforced Nylon 6 (PA6-CF) for FDM 3D printing from 3DXTECH. It was developed as a drop-in alternative to Markforged Onyx, with a matte black finish and good toughness. In 3DXTECH’s side-by-side testing, Obsidian v2 is stiffer than Onyx in every orientation tested, with similar strength and heat resistance, which makes it a strong choice for jigs, fixtures, and functional parts.


What Obsidian Nylon 6+CF Is Best For

  • Jigs, fixtures, and assembly aids
  • End-of-arm tooling and gripper fingers
  • End-use mechanical components and brackets
  • Automotive brackets and housings
  • Aerospace tooling
  • Replacing parts printed in Markforged Onyx

When another material is a better fit

  • Need higher stiffness and heat resistance: PPA-CF
  • Need UV resistance for outdoor parts: ASA+CF
  • Need a nylon part with fine detail: MJF Nylon 12

Key Material Facts

  • Carbon fiber reinforced Nylon 6 copolymer
  • Drop-in alternative to Markforged Onyx
  • Stiffer than Onyx in every orientation 3DXTECH tested
  • Heat deflection temperature: 147°C (297°F) at 0.45 MPa
  • High impact toughness: 854 J/m unnotched Izod
  • Matte black surface that hides layer lines

Obsidian Nylon 6+CF Material Properties

Version note: we print Obsidian Nylon 6+CF v2 from 3DXTECH, using 3DXTECH’s published data (TDS Rev 1.0) for the values below.

Mechanical properties compared to Markforged Onyx (from 3DXTECH’s published data sheet; both materials printed on the same Markforged X7 at 0.20 mm layers with solid infill and tested by an independent lab)

Property (orientation)Obsidian v2OnyxMethod
Tensile strength (flat)23.8 MPa26.1 MPaASTM D638
Tensile modulus (flat)731 MPa540 MPaASTM D638
Tensile strength (edge)31.0 MPa31.9 MPaASTM D638
Tensile modulus (edge)1,510 MPa1,207 MPaASTM D638
Tensile strength (vertical)23.4 MPa20.1 MPaASTM D638
Tensile modulus (vertical)1,351 MPa1,083 MPaASTM D638
Flexural strength (edge)33.9 MPa30.8 MPaASTM D790
Flexural modulus (edge)1,048 MPa821 MPaASTM D790
Unnotched Izod impact (flat)854 J/m940 J/mASTM D256
Heat deflection temperature @ 0.45 MPa147°C (297°F)145°C (293°F)ISO 75
Density1.2 g/cm³–ISO 1183

More information on Obsidian Nylon 6+CF is available from 3DXTECH, the material manufacturer.


We print Obsidian Nylon 6+CF on our FDM print farm, which limits single parts to 13.38″ × 12.59″ × 13.38″. For larger parts, we can run materials such as ABS or PC-ABS on our large-format FDM systems. For structural parts, we recommend solid infill.

FDM parts are strongest along the layers and weaker between them, so we orient each part to put strength where it is needed. Tell us how your part will be loaded when you request a quote. Our FDM Part Design Guide covers wall thickness, orientation, supports, and threaded inserts.


Finish and Color Options

Obsidian Nylon 6+CF parts are black with a matte carbon fiber surface. We ship FDM parts with a strip and ship finish: we break away the supports and send the part with layer lines visible. Sanding, painting, heat-set threaded inserts, and other higher levels of finish are available on request and quoted per part. See all of our finishing and post-processing options.



Obsidian Nylon 6+CF Material Testing Videos



Obsidian Nylon 6+CF FAQ

What is Obsidian Nylon 6+CF made of?

It is a Nylon 6 (PA6) copolymer reinforced with high-modulus chopped carbon fiber.

Is it a good replacement for Markforged Onyx?

Yes. 3DXTECH developed Obsidian v2 as a drop-in alternative to Onyx. In independent testing on the same Markforged X7, Obsidian v2 was stiffer than Onyx in every orientation, with similar strength and heat deflection temperature.

Can it be used for end-use parts?

Yes. Its stiffness, toughness, and heat resistance make it a good fit for fixtures, tooling, brackets, and other functional end-use components.

How big can Obsidian Nylon 6+CF parts be?

Single parts can be up to 13.38″ × 12.59″ × 13.38″. Larger parts can be printed in sections and bonded, or printed in another material on our large-format FDM systems.

If you like what you see...

You should sign up for our quarterly email newsletter! We send out a summary of all the latest testing videos, design guides, and anything else cool that has been added to the F3DP website 4 times a year.

We hate spam as much as you do so we only send all killer content and no filler BS!

facebook twitter instagram youtube