FDM – TPU 3D Printing Materials
TPU (thermoplastic polyurethane) is a flexible, rubber-like material for FDM 3D printing. It stretches, bends, and springs back, and it holds up to abrasion, oils, and greases. We print TPU in four hardness levels, from soft and squishy 85A to stiff, tough 68D, so you can pick the right balance of flexibility and strength for your part. Our shop is in Coopersville, Michigan, just west of Grand Rapids, and we ship parts nationwide.
Compare TPU 3D Printing Materials by Hardness
All four TPU 3D printing materials are compared below. Hardness runs from softest (85A) to stiffest (68D). X-Y values are for parts printed flat; Z values are measured across the layers.
| Property | TPU 85A | TPU 90A | TPU 95A HF | TPU 68D |
|---|---|---|---|---|
| Shore hardness | 85A | 90A | 95A | 68D |
| Feel | Soft and squishy | Firm rubber | Firm, tough rubber | Stiff, tough plastic |
| Density (ISO 1183) | 1.18 g/cm³ | 1.24 g/cm³ | 1.22 g/cm³ | 1.26 g/cm³ |
| Tensile strength, X-Y | 12.0 MPa (1,740 psi) | 12.5 MPa (1,810 psi) | 27.3 MPa (3,960 psi) | 22.4 MPa (3,250 psi) |
| Tensile strength, Z | 10.5 MPa | 10.1 MPa | 22.3 MPa | 11.2 MPa |
| Young’s modulus, X-Y | 6.8 MPa | 5.3 MPa | 9.8 MPa | 1,190 MPa |
| Elongation at break, X-Y | > 700% | > 650% | > 650% | > 650% |
| Elongation at break, Z | > 350% | > 350% | > 480% | 31% |
| Best for | Cushions, grips, impact absorbers | Shoe soles, grips, RC tires | Wear parts, bumpers, protective covers | Tough clips, bumpers, wear pads |
What TPU 3D Printing Materials Are Best For
- Bumpers, feet, and vibration dampers
- Protective covers, cases, and grips
- Cable strain reliefs and grommets
- Wearable straps and bands
- Flexible hinges and joints
- Shoe soles, tires, and other wear parts
Key Material Facts
- Rubber-like elasticity, with Shore hardness from 85A to 68D
- High elongation at break: more than 650% in most grades
- Resistant to abrasion, oils, and greases
- Holds up to repeated bending, flexing, and impact
- Density from 1.18 to 1.26 g/cm³, depending on hardness
- Printed in a range of colors
Other rubber-like materials we offer
- Need many small flexible parts with fine detail: MJF TPU
- Need a soft, highly detailed rubber part: SLA Flexible 50A or Flexible 80A
- Need a silicone-like part: SLA Silicone 40A
- Not sure which rubber to pick: see our 3D printed rubber part comparison guide
TPU 85A – Maximum Flexibility
TPU 85A is the softest TPU we offer. It provides excellent cushioning, impact absorption, and a soft, rubbery feel for parts where softness matters most.
- Cushioning pads and impact absorbers
- Soft grips and protective cases
- Squeezable and wearable parts
TPU 85A properties
| Property | Value | Method |
|---|---|---|
| Shore hardness | 85A | – |
| Density | 1.18 g/cm³ (0.043 lb/in³) | ISO 1183 |
| Young’s modulus, X-Y / Z | 6.8 / 5.2 MPa | ISO 527 |
| Tensile strength, X-Y / Z | 12.0 / 10.5 MPa | ISO 527 |
| Elongation at break, X-Y / Z | > 700% / > 350% | ISO 527 |
| Impact strength, X-Y / Z | 124.3 / 88.5 kJ/m² | ISO 179 |
| Melting temperature | 177°C (351°F) | DSC |
| Melt index (210°C, 2.16 kg) | 8.76 ± 2.6 g/10 min | – |
| Water absorption (25°C, 55% RH) | 0.67% | – |
TPU 85A flex and abuse testing
TPU 85A test prints








TPU 90A – Balanced Strength and Flexibility
TPU 90A sits between soft and firm. It has more structure than 85A while staying flexible, with excellent wear resistance after repeated bending, so it suits shoe soles, grips, RC tires, and protective parts.
- Shoe soles and footwear prototypes
- Grips, handles, and overmold prototypes
- RC tires and wheels
TPU 90A properties
| Property | Value | Method |
|---|---|---|
| Shore hardness | 90A | – |
| Density | 1.24 g/cm³ (0.045 lb/in³) | ISO 1183 |
| Young’s modulus, X-Y / Z | 5.3 / 4.4 MPa | ISO 527 |
| Tensile strength, X-Y / Z | 12.5 / 10.1 MPa | ISO 527 |
| Elongation at break, X-Y / Z | > 650% / > 350% | ISO 527 |
| Impact strength, X-Y / Z | 124.2 / 87.3 kJ/m² | ISO 179 |
| Melting temperature | 180°C (356°F) | DSC |
| Melt index (210°C, 2.16 kg) | 9.36 ± 2.6 g/10 min | – |
| Water absorption (25°C, 55% RH) | 0.61% | – |
TPU 90A flex and abuse testing
TPU 90A test prints








TPU 95A HF – Firm and High Strength
TPU 95A HF is a firm TPU with the highest tensile strength of our flexible grades, while still stretching more than 650% before breaking. It is ideal for bumpers, protective covers, and functional parts that must stand up to wear.
- Bumpers, feet, and vibration dampers
- Wear parts and protective covers
TPU 95A HF properties
| Property | Value | Method |
|---|---|---|
| Shore hardness | 95A | – |
| Density | 1.22 g/cm³ (0.044 lb/in³) | ISO 1183 |
| Young’s modulus, X-Y / Z | 9.8 / 7.4 MPa | ISO 527 |
| Tensile strength, X-Y / Z | 27.3 / 22.3 MPa | ISO 527 |
| Elongation at break, X-Y / Z | > 650% / > 480% | ISO 527 |
| Impact strength, X-Y / Z | 123.2 / 86.3 kJ/m² | ISO 179 |
| Melting temperature | 183°C (361°F) | DSC |
| Melt index (210°C, 2.16 kg) | 36.5 ± 2.6 g/10 min | – |
| Water absorption (25°C, 55% RH) | 1.08% | – |
TPU 95A HF flex and abuse testing
TPU 95A HF test prints








TPU 68D – Rigid Toughness
TPU 68D is the stiffest TPU we offer. In fact, it behaves more like a tough plastic than a rubber, with limited flexibility and very high toughness, so it fits clips, bumpers, and wear pads that need to flex a little without cracking.
- Tough clips, latches, and wear pads
- Bumpers and guards that see repeated impact
- Parts that need to flex slightly without cracking
TPU 68D properties
| Property | Value | Method |
|---|---|---|
| Shore hardness | 68D | – |
| Density | 1.26 g/cm³ (0.046 lb/in³) | ISO 1183 |
| Young’s modulus, X-Y / Z | 1,190 / 600 MPa | ISO 527 |
| Tensile strength, X-Y / Z | 22.4 / 11.2 MPa | ISO 527 |
| Elongation at break, X-Y / Z | > 650% / 31% | ISO 527 |
| Impact strength, X-Y / Z | 124.3 / 9.6 kJ/m² | ISO 179 |
| Melting temperature | 183°C (361°F) | DSC |
| Melt index (210°C, 2.16 kg) | 21.8 ± 0.3 g/10 min | – |
| Water absorption (25°C, 55% RH) | 1.20% | – |
TPU 68D flex and abuse testing
TPU 68D test prints








Designing Flexible TPU Parts
With FDM TPU, the hardness of the filament is only part of the story. Wall count and infill density change how soft a part feels: a 95A part with a light infill can feel softer than a solid 90A part. Tell us how the part should feel and we will set it up to match, or we can print test coupons first.
However, like all FDM parts, TPU is weaker across the layers. The difference is biggest in 68D, which stretches more than 650% along the layers but only 31% across them, so we orient parts so the main stretch runs along the layers. Very thin walls and fine features are hard to print cleanly in the softest grades, so keep walls at least 1.5–2 mm (0.06–0.08″) thick where you can.
Our FDM Part Design Guide covers wall thickness, orientation, and supports for FDM parts.
Finish and Color Options
We stock TPU in a range of colors. We ship FDM parts with a strip and ship finish: we break away the supports and send the part with layer lines visible. Higher levels of finish are available on request and quoted per part. See all of our finishing and post-processing options.
TPU Rocket Testing Video
Watch the full rocket testing video.
TPU 3D Printing FAQ
What is the density of TPU?
The density of TPU is about 1.18 to 1.26 g/cm³, depending on hardness. Our TPU 85A is 1.18 g/cm³, 90A is 1.24 g/cm³, 95A HF is 1.22 g/cm³, and 68D is 1.26 g/cm³.
Which TPU hardness should I choose?
Choose 85A for the softest, most cushioned parts, 90A for a firm but flexible rubber feel, 95A HF for wear parts, bumpers, and covers that need strength, and 68D when you need a tough part that only flexes a little. If you are not sure, tell us what the part does and we will recommend one.
How strong is TPU?
Among our TPU 3D printing materials, tensile strength ranges from about 12 MPa for 85A and 90A to 27 MPa for 95A HF, with elongation at break above 650%. TPU parts stretch a long way before they tear.
How does FDM TPU compare to MJF TPU or SLA flexible resins?
FDM TPU is the most economical choice for one-off and larger flexible parts, and it comes in the widest range of hardness. MJF TPU is better for many small parts with fine detail, and SLA Flexible 50A or Silicone 40A gives the smoothest surface and finest features.
Can I use FDM TPU for seals and gaskets?
Not for working seals. FDM parts are built from extruded beads of plastic, so they have small gaps and leak paths between the layers, and they will not hold a vacuum or pressure. For a seal you plan to test or use, choose SLA Flexible 50A, Flexible 80A, or Silicone 40A. We have printed seals in these materials that passed vacuum and pressure decay testing.
FDM TPU can still be useful for look-and-feel and fit-check models of flat gaskets, for example to check that retention features hold a seal in its groove during assembly. It does not print round O-ring style cross sections well.
Is TPU resistant to oils and chemicals?
TPU resists abrasion, oils, and greases well, which is why it works well for wear parts, bumpers, and covers. It is not resistant to acids, alkalis, or some organic solvents, so tell us what chemicals your part will see.
Related Resources
- FDM 3D printing overview
- FDM part design guide
- Accuracy of 3D printed parts
- Machine and material comparison
- 3D printed rubber part comparison guide
If you like what you see...
You should sign up for our quarterly email newsletter! We send out a summary of all the latest testing videos, design guides, and anything else cool that has been added to the F3DP website 4 times a year.
We hate spam as much as you do so we only send all killer content and no filler BS!